Refrigerator repair in Castro Valley CA

Is your fridge not getting as cold as it should anymore?

Supposing it worked fine before, which means it's not a manufacturing defect, we can narrow down the likely causes to a handful of things. The most obvious cause would be accidentally lowering the temperature control. If this isn't the issue, we would then want to consider what else could be at fault.

The first thing we recommend testing is a break in the door seal (gasket). Even a pinhole can result in cold air escaping which thwarts temperature regulation within the unit. You can clean off the gasket and then rub petroleum jelly over it to tackle minor openings. However, the seal will need replaced sooner rather than later if this is the true cause of your fridge's inability to stay cold enough.

Next, clear off any dirt that is piling on your fridge's compressor. This cleaning process should be done every three months maximum, especially for pet owners. The dirt, hair and debris buildup on the coils can severely hamper the fridge's ability to reach and hold cold temperatures.

Washer repair in Castro Valley CA

We do not recommend a DIY washer repair very often.

Most issues need to be diagnosed with live voltage testing / require a multimeter for you to properly troubleshoot. This part of the process should definitely be left in the hands of a professional. By then, if you just need a minor repair, once you have your service call fee waived it won't cost much at all to get the washer working again.

However, it's understandable that some appliance owners will take the DIY route before calling in ann appliance repair professional. It's also true that there are a few issues with washing machines that can be tackled by an 'average Joe', with the right tools.

A defective lid switch is something that many people can replace on their own. This problem is also easy to discover without extensive diagnosing as well. In fact, the main indication of a faulty lid switch is pretty noticeable - your machine will fill up but then do nothing at all. However, a multimeter checking for continuity is the only guaranteed way to diagnose a lid switch problem.

Dryer repair in Castro Valley CA

Is your dryer not spinning anymore?

We recommend a professional diagnosis but will go over some ways you could potentially troubleshoot the issue on your own. Thankfully, this issue is one of the few problems that often does not require a multimeter to make an accurate diagnosis.

A dryer will stop spinning if the dryer belt snaps. It's possible for this to happen simply because of wear and tear to the belt over time. Running heavy loads regularly can also increase the risk of the belt snapping prematurely. The best way to tell if this part needs to be replaced is by attempting to spin the dryer by hand. If there's no resistance, that's your problem.

Another possible reason for a dryer to stop spinning is because a drum roller (or both) has become faulty. Just like the belt, the rollers are susceptible to wear and tear. To diagnose, take the dryer belt out of your machine and see if you can get the inside to spin with ease. If there's resistance still, inspect the rollers for damage.

Dishwasher repair in Castro Valley CA

Many issues can plague a dishwasher and cause it to perform poorly or make it not work at all. If your machine is suddenly problematic, we advise that you schedule a service call with an experienced dishwasher repair technician. However, a few steps can be taken to attempt to diagnose the issue on your own end first.

What is wrong with your dishwasher?

Does it fail to fill up?

If so, make sure the water supply line wasn't inadvertently shut off. Be sure the fill hose isn't tangled: Check the water valve filter in case it clogged up from debris accumulation. With a multimeter, ensure the water inlet valve has proper continuity as well to verify it's opening when the fill cycle runs.

Does it fail to drain?

If so, make sure the drain hose isn't clogged. Take off the hose and attempt to blow through it to see if anything comes out. Make sure the drain and its filter isn't clogged as well. While the issue rarely lies here, inspect the disposer inlet to make sure it's properly connected. Lastly, run a continuity test with your multimeter on drain pump motor as this motor is responsible for activating the drain cycle.

Freezer repair in Castro Valley CA

Is your freezer working intermittently?

If it starts to work and stops working all on its own, a handful of problems might be occurring. We'll go over each of them to help you figure out what might be wrong with your freezer. Take each into consideration but reach out for a diagnosis with a licensed freezer repair technician to get to the bottom of the problem.

Check the condenser fan. If it's clogged up, the machine might start to overwork and shut off when it pushes itself too much. Not only can clogs cause this issue but the fan, or other parts, could be shorting out while the machine is in use. This problem might happen if the parts become loose - if they do become loose, chances are you will also hear a rattling noise.

Check the compressor relay. This part is in charge of the compressor and tells it when to run and when to turn off. If it's faulty, the freezer will be told to turn off at the wrong time. Therefore, your freezer might run intermittently if the compressor relay needs to be replaced.

Oven repair in Castro Valley CA

Ever wonder what are the most common oven repair calls that appliance repair companies receive from people like you?

The average residential customer comes to us to tackle a common range of issues. We'll go over them below to help you familiarize yourself with what kinds of issues regularly occur among most appliance repair company's oven repair clientele.

Firstly, and most commonly, countless oven repair calls come in from appliance owners with ovens that don't regulate heat properly. The lack of fluid control of the internal temperatures by the oven is extremely problematic. You don't want food to be undercooked or to have to resort to slightly burning meals to ensure you avoid getting sick.

Second, many calls come in from clients that have no heat production at all. This issue often arises from a bake or broil element shorting out or becoming physically damaged. Replacing these elements is not rocket science but can be very dangerous, especially if you don't exercise precaution from an electrical safety standpoint.

Range/Stove repair in Castro Valley CA

Is the pilot light on your gas stove not igniting or staying lit?

This problem could be attributed to many different issues. Some of the stove repair solutions for a pilot light that won't light are easy to handle on your own. However, most gas-related problems are best left in the hands of a licensed professional. Also, it's important to remember that gas leaks can be fatal and it's possible to trigger one if you don't know what you're doing.

Anyhow, the average stove owner can get away with manually testing the pilot light. If it's not lighting, try drying it off with a paper towel first - in case any food or grease is gumming it up. This will give you a better chance to get the pilot light to work. For safety purposes, it's recommended that you try lighting with a match - your fingers will be further away from the gas hole opening this way.